Currently Empty: EGP0.00
Dental Impression Materials
Impression Compound™
Impression Compound™
Kerr
Impression Compound™ For Full/Partial Impressions or Copper Bands/Tracing Impression Compound is a thermoplastic impression material available in cakes – for full or partial impressions – and sticks – for copper band impressions and for adding to the periphery of an impression tray. Each coloured variant has a controlled working temperature. Red (temp 55°C) Green (temp …
Continue reading Impression material
Blu-Mousse®
Blu-Mousse®
Parkell
Blu-Mousse® Bite Registration Material from Parkell Bite registrations, matrices, model bases, bite plates and now CAD scanning capabilities—the uses for Blu-Mousse® just keep growing! For over twenty years, Blu-Mousse has been a favorite VPS material in dental offices world-wide. Originally intended as a bite registration material, Blu-Mousse has evolved into a VPS with a “can-do” …
Continue reading Blu-Mousse® Bite Registration material
Out Of Stock
Mach-SLO™
Mach-SLO™ Die-Silicone
Parkell
Mach-SLO™ Die-Silicone On the bench, it sets in two minutes, while in the mouth it sets in 90 seconds. It’s a smart choice for intraoral use or when making complex models. • Flows beautifully—better than stone—to create a smoother die and to capture minute detail. • No hand-mixing—inject it directly from the automix cartridge into …
Continue reading Mach Die – Silicone Impression
Cinch®
Cinch®
Parkell
Cinch® • Exceptionally accurate, hydrophilic and strong. • Use as a final impression material or an alginate substitute. • 90 sec. set, 60 sec. working time. • Cinch is available in a wide variety of viscosities, final hardness and setting times. SIMPLIFY YOUR OPERATORY. If you are switching between a VPS material for final impressions …
Continue reading Cinch® Impression material
Detaseal
Putty Soft
DETAX
New hydroflow silicone impression material, high consistency, kneadable. Fluffy-soft initial consistency with simultaneously reduced final hardness (60 Shore A). For all precision impression techniques in combination with Detaseal® hydroflow lite/Xlite. Mixing & demoulding with unprecedented ease. Time savings due to a shorter curing time (2:45 min.) with a sufficient processing time of 1:15 min. Maximum …
Continue reading Addition Silicone Impression
Detaseal mono
Rubber base
DETAX
Hydroflow mono-phase impression silicone, medium tray consistency for single step impression-taking or mixed technique, with distinct snap set. Constant precision, especially in humid areas, due to hydrophilic activation of the surface. Highly thixotropic, flows under pressure. Very tear-resistant with high, elastic recovery from deformation (99.8% ), easy to remove. Fast set (total 3:30 min.), dimensional …
Continue reading Addition Silicone Impression
Take 1™ Advanced™
Take 1™ Advanced™
Kerr
Take 1™ Advanced™ VPS Impression Material Take 1™ Advanced™ VPS impression material combines Kerr’s expertise in developing high-performance impression materials with recent technological advancements. Take 1™ Advanced™ is first system of VPS materials with an optimum combination of physical properties: strength, elasticity, dimensional stability and the ability to register detail in any environment. Take 1™ …
Continue reading Take 1™ Advanced™ Impression material
Mollosil plus
Soft liner
DETAX
Long-term soft relining material for chairside use, A-silicone based, cold curing, biocompatible. The material is directly applied from the cartridge onto the denture base. Strong bonding to the denture acrylic. Also suitable for application with the indirect technique. Primer with colour indicator for better application check. Booklets for patients and grinding set inclusive. Medical device …
Continue reading Soft Reliner
Showing all 8 results